Running this spray booth for twenty minutes requires 262,080 cubic feet of available air. Occupational Safety and Health Administration, Regulations (Standards - 29 CFR) - Table of Contents, Severe Storm and Flood Recovery Assistance, Occupational Health and Environmental Control. Answer 1: For purposes of OSHA's standard at 29 CFR 1910.94(c), which addresses ventilation requirements for spray finishing operations, the determination of whether such activities must be conducted in a spray booth or spray room is based on the presence of a hazardous chemical in the paint. During spray jobs in a paint booth, the exhaust system must draw substantial quantities of air out of the shop in order to operate. 800-321-6742 (OSHA) 200 Constitution Ave NW Washington, DC 20210 800-321-6742 (OSHA) TTY For this example, let’s use 50 FPM. These volumes must be replenished with equal volumes of air coming into the booth. Important codes that paint booths comply with include National Fire Code 1, NFPA 33, OSHA, and a few others. Spray booths or spray rooms … The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Automotive paint booths are designed to move a specific volume of air, which will cause a certain amount of restriction to the system – what they call “static pressure.” As this increases, the amount of air flowing in and out of the booth will decrease. A suitable standard for maintaining and testing is AS/NZS 4114.2: 2003 Spray painting booths, designated spray painting areas and paint mix rooms - Part 2: Installation and maintenance. Users must request such authorization from the sponsor of the linked Web site. This requires a building at least 17,472 sq ft with 15’ ceilings or 10,483 sq ft with 20’ ceilings. Each ventilation unit should have an independent exhaust unit. One hundred feet per minute is the guideline for air movement in the booth area. Multiply the booth's face area by 100 feet per minute to achieve CFM. Fire prevention measures are included in both the paint spray booth design and the process flow. The total flow through the booth (16 x 40 x 50) would be 32,000 CFM. Spray Booths: 29CFR 1910.94c, ACGIH Industrial Ventilation ANSI/AIHA Z9.3-2007 . Please click the button below to continue. There must be some sort of independent exhaust system in place to discharge outside of the building. Fans should be made of nonferrous or nonsparking material. All our spray booth engineers are required to undertake on-going training and assessment to ensure they are fully conversant with new spray booth regulations, guidelines and best practices across all types of spray booth testing. ANSI/ASHRAE 62.1-2010 . (a) General. (1) Mechanical ventilation shall be kept in operation … If a downdraft paint booth is 16 feet wide and 14 feet tall, typical air velocity in the booth would be 50 to 100 FPM. The minimum distance … Paint booth air flow requirements OSHA : OSHA states that paint booths must be designed to filter out flammable contaminants and move air currents toward an exhaust for proper ventilation. Welding ; Local Exhaust Ventilation (LEV) OSHA requires 100 feet per minute (fpm) in the zone of welding for a local exhaust hood. Ventilation Requirements Ventilation should be kept on during and after all spraying operations for a sufficient time to dissipate vapors. Spray coating operations whenever practicable shall be confined to properly designed, constructed and adequately ventilated spray booths or spray rooms which meet all the requirements of both this section and Article 137. Washington, DC 20210 Dividing the flow rate by the volume (32,000 / 8,960) gives 3.5 air changes per minute. Ventilation. (b) Operation. Section 1910.94(c)(2) provides: (2) Location and Application. It’s simple…. Ventilation and Personal Protective Equipment Requirements for Spray Coating Operations. There are booth ventilation requirements to reduce the buildup of flammable material. The following is an abbreviated version of OSHA requirements. www.OSHA.gov, Occupational Safety and Health Administration Paint booth regulations exist to help ensure the proper construction, operation and maintenance of spray booths to further limit liability. TTY This is the size of the fan needed. The velocity is half that of the previous example, but the air change is higher. All electrical and combustible materials inside the booth and within 20 feet of the booth are covered under OSHA standards. The best way to make sure your paint booth ventilation is up to OSHA requirement is to hire the services of an authorized paint booth contractor. Because spray paint materials are often caustic, flammable and potentially toxic to both employees and the environment, spray booths are utilized to protect operators through effective ventilation and contained exposure. 200 Constitution Ave NW 1910.94 (a) (7) Operational procedures and general safety. Spray Booth Design Requirements Tested By Qualified Engineers. The OSHA criteria for design and construction of spray paint booths and ventilations are many wide-ranging, can confuse and be overwhelming. Other requirements exist for fixed enclosure welding and confined space welding. Using the example from above, 80 square feet multiplied by 100 feet per minute equals 8,000 CFM. Thank you for visiting our site. Occupational Safety and Health Administration An adequate amount of ventilation air is needed to avoid saturating the air with enough … AIR MAKE-UP (AMU) is defined as…a mechanical means of replacing air that has been exhausted out of the booth. it’s all about paint booth air flow. Paint booths are designed to meet a minimum air flow requirement to be compliant with national codes that govern spray booths. Finally, all metal parts of the spray booth must be properly grounded. This issue of an undersized building can be addressed with booth design and/or an air make-up unit. Air for abrasive-blasting respirators shall be free of harmful quantities of dusts, mists, or noxious gases, and must meet the requirements for supplied-air quality and use specified in 29 CFR 1910.134 (i). All open flames, heat and spark producing equipment must be kept 20 feet from the booth unless separated by a partition. Mechanical ventilation is a specified system and must therefore be included on compliance schedules for spray booths and paint mixing rooms. For a good overview of all paint booth code compliance check out this article. The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. So, it is important to have an automotive paint booth that is not only properly isolated but also has the right ventilation system. www.OSHA.gov. Chapter 21, “Paint Spray Operations” NFPA 91 .